How To Close An Above Ground Pool With A Sand Filter

Endmost an Above Ground Puddle for the Winter

At the end of the swimming season, you must follow these directions to winterize and make your pool ready for the Winter. The following guide will work for above ground pools sanitized using chlorine or common salt h2o.

Step 1) Prior to Closing

Several days prior to endmost your pool, test the water for the pH level, total alkalinity, and chlorine / salt water levels. The water balance is important to protect the pool from corrosion or scale build-up during Winter shut downwards.

Step 2) Perform a Consummate Inspection

a) Finding Leaks

Caution: Make certain the pool is not leaking before roofing. Serious structural impairment tin can occur if leaks get undetected through Winter shut down from water ice movement. Maintain a strict leak inspection during the fall, Winter and Leap months.

To determine if the puddle is leaking, mark the liner at the h2o level with a non-permanent marking device such as tape or a wax pencil and observe the water level in the pool for ten to 14 days after the pool has been airtight for the flavour.
b) Check the Liner

Make sure the top of the liner is still attached to the pool wall. Make sure in that location are no leaks. Repair any liner holes with a vinyl patch: any minor punctures in the liner can exist easily repaired with underwater repair kits available at Pool Supplies Canada. Do non remove the liner from the pool, as removal of the liner volition void the existing warranty.
c) Bank check all Joints and Screws

Make sure all the frame joints are fitting together properly and make sure the pool wall has non shifted from the lesser rail. Ensure all screws and bolts are tight.
d) Bank check for Rust

Periodically audit the metal parts for any corrosion – particularly effectually the skimmer area. If corrosion is found, immediate cosmetic action must be taken. Wire brush whatsoever rust and add a coat of enamel primer followed by a glaze of color matching anti-rust enamel paint. Puddle structure failure could result in major property harm and bodily harm. Paint whatever scratches with anti-rust paint.

Step 3) Add Closing Chemicals

Add together your puddle closing chemical kit and permit chemicals to circulate. If yous have a salt water puddle, use a closing chemic kit with a non-chlorine stupor product, like our very own Pool Supplies Canada Premium Pool Endmost Chemical Kit.

Step 4) Lower the H2o Level

a) Lower the h2o level in your pool until it is nearly 6" (15 cm) below the skimmer opening. You may plug the return jet hole at this time.** IMPORTANT ** Practise NOT PLUG THE SKIMMER DRAIN Hole (located at the base of the skimmer). Remove all hoses attached to the skimmer and return fittings. Do not let water freeze in the skimmer. Exit the skimmer attached to the pool wall and ensure that the skimmer lid is installed.DO NOT Bleed ALL THE Water OUT OF THE POOL.

Please Note: in areas where temperatures consistently reach -30 to -40 degrees, lower the water level until it is nearly xviii" (46 cm) deep and do not utilize a winter cover or alternatively ensure minimal accumulation of snowfall, water ice or water on peak of the embrace.DO Not Drain ALL THE H2o OUT OF THE POOL. If you lot wish to keep more so 24" of water in your pool, please see your local dealer for assistance.
b) The inside water level must be maintained at least 3" (76 mm) beneath the skimmer opening throughout the wintertime. Surplus water must be removed past pumping, draining or siphoning, so that information technology doesn't enter the skimmer during the winter period.

Or
c) Ensure skimmer drain is left open and unobstructed so water can freely menses out.Practise NOT PLUG THE SKIMMER. Remove all hoses attached to the skimmer and return fittings. Do not let water freeze in the skimmer. Exit the skimmer fastened to the pool wall and ensure that the skimmer lid is installed.

Step 5) Filter Preparation

Disconnect the hoses from the filter. Follow the closing instructions in your filter manual.

Step half-dozen) Install Your Winter Cover

At present you tin cover your above footing pool with a Winter pool comprehend. It should exist in a state of good repair to do the best possible task of protecting your pool through the Winter months. Feed the cable through each grommet hole in the cover and secure tightly using the winch to prevent the edges of the cover from being caught by blowing current of air. If you are installing an Eliminator Winter Cover, follow the instructions included with the production, as installation of these types of covers will vary.

In one case your Winter embrace has been installed, ensure it is sitting on the water properly according to the diagram below.

Proper Winter Cover Installation